This function computes the maximum likelihood estimates of the parameters of a diversity-dependent diversification model with shifting parameters at time t = tshift for a given set of phylogenetic branching times. It also outputs the corresponding loglikelihood that can be used in model comparisons.
dd_SR_ML(
brts,
initparsopt = c(0.5, 0.1, 2 * (1 + length(brts) + missnumspec), 2 * (1 + length(brts) +
missnumspec), max(brts)/2),
parsfix = NULL,
idparsopt = c(1:3, 6:7),
idparsfix = NULL,
idparsnoshift = (1:7)[c(-idparsopt, (-1)^(length(idparsfix) != 0) * idparsfix)],
res = 10 * (1 + length(brts) + missnumspec),
ddmodel = 1,
missnumspec = 0,
cond = 1,
btorph = 1,
soc = 2,
allbp = FALSE,
tol = c(0.001, 1e-04, 1e-06),
maxiter = 1000 * round((1.25)^length(idparsopt)),
changeloglikifnoconv = FALSE,
optimmethod = "subplex",
num_cycles = 1,
methode = "analytical",
verbose = FALSE
)gives the maximum likelihood estimate of lambda before the shift
gives the maximum likelihood estimate of mu before the shift
gives the maximum likelihood estimate of K before the shift
gives the maximum likelihood estimate of lambda after the shift
gives the maximum likelihood estimate of mu after the shift
gives the maximum likelihood estimate of K after the shift
gives the time of the shift
gives the maximum loglikelihood
gives the number of estimated parameters, i.e. degrees of feedom
gives a message on convergence of optimization; conv = 0 means convergence
A set of branching times of a phylogeny, all positive
The initial values of the parameters that must be optimized
The values of the parameters that should not be optimized
The ids of the parameters that must be optimized, e.g. 1:7
for all parameters. The ids are defined as follows:
id == 1 corresponds
to lambda (speciation rate) before the shift
id == 2 corresponds to mu
(extinction rate) before the shift
id == 3 corresponds to K (clade-level
carrying capacity) before the shift
id == 4 corresponds to lambda
(speciation rate) after the shift
id == 5 corresponds to mu (extinction
rate) after the shift
id == 6 corresponds to K (clade-level carrying
capacity) after the shift
id == 7 corresponds to tshift (the time of
shift)
The ids of the parameters that should not be optimized, e.g. c(1,3,4,6) if lambda and K should not be optimized, but only mu. In that case idparsopt must be c(2,5,7). The default is to fix all parameters not specified in idparsopt.
The ids of the parameters that should not shift; This can only apply to ids 4, 5 and 6, e.g. idparsnoshift = c(4,5) means that lambda and mu have the same values before and after tshift
sets the maximum number of species for which a probability must be computed, must be larger than 1 + length(brts)
sets the model of diversity-dependence:
ddmodel == 1 : linear dependence in speciation rate
ddmodel == 2 : exponential dependence in speciation rate
ddmodel == 2.1 : variant of exponential dependence in speciation rate with offset at infinity
ddmodel == 2.2 :
1/n dependence in speciation rate
ddmodel == 3 : linear dependence in extinction rate
ddmodel == 4 : exponential dependence in extinction rate
ddmodel == 4.1 : variant of exponential dependence in extinction rate
with offset at infinity
ddmodel == 4.2 : 1/n dependence in extinction rate
with offset at infinity
The number of species that are in the clade but missing in the phylogeny
Conditioning:
cond == 0 : no conditioning
cond == 1 : conditioning on non-extinction of the phylogeny
cond == 2 : conditioning on non-extinction of the phylogeny and on the total
number of extant taxa (including missing species)
cond == 3 : conditioning on the total number of extant taxa (including missing
species)
Note: cond == 3 assumes a uniform prior on stem age, as is the standard
in constant-rate birth-death models, see e.g. D. Aldous & L. Popovic 2004.
Adv. Appl. Prob. 37: 1094-1115 and T. Stadler 2009. J. Theor. Biol. 261:
58-66.
Sets whether the likelihood is for the branching times (0) or the phylogeny (1)
Sets whether stem or crown age should be used (1 or 2)
Sets whether a search should be done with various initial conditions, with tshift at each of the branching points (TRUE/FALSE)
Sets the tolerances in the optimization. Consists of:
reltolx
= relative tolerance of parameter values in optimization
reltolf =
relative tolerance of function value in optimization
abstolx = absolute
tolerance of parameter values in optimization
Sets the maximum number of iterations in the optimization
if TRUE the loglik will be set to -Inf if ML does not converge
Method used in optimization of the likelihood. Current default is 'subplex'. Alternative is 'simplex' (default of previous versions)
the number of cycles of opimization. If set at Inf, it will do as many cycles as needed to meet the tolerance set for the target function.
The method used to solve the master equation, default is 'analytical' which uses matrix exponentiation; alternatively numerical ODE solvers can be used, such as 'odeint::runge_kutta_cash_karp54'. These were used in the package before version 3.1.
Show the parameters and loglikelihood for every call to the loglik function
Rampal S. Etienne & Bart Haegeman
The output is a dataframe containing estimated parameters and maximum loglikelihood. The computed loglikelihood contains the factor q! m!/(q + m)! where q is the number of species in the phylogeny and m is the number of missing species, as explained in the supplementary material to Etienne et al. 2012.
- Etienne, R.S. et al. 2012, Proc. Roy. Soc. B 279: 1300-1309,
doi: 10.1098/rspb.2011.1439
- Etienne, R.S. & B. Haegeman 2012. Am. Nat.
180: E75-E89, doi: 10.1086/667574
dd_SR_loglik, dd_ML,
dd_KI_ML,
cat("This will estimate parameters for a sets of branching times brts without conditioning.\n")
cat("The tolerance of the optimization is set ridiculously high to make runtime fast.\n")
cat("In real applications, use the default or more stringent settings for tol.\n")
brts = 1:10
dd_SR_ML(brts = brts, initparsopt = c(0.4581, 1E-6, 17.69, 11.09, 8.9999), idparsopt = c(1:3,6,7),
idparsfix = NULL, parsfix = NULL, idparsnoshift = c(4,5), cond = 0,
tol = c(1E-1,1E-1,1E-1),optimmethod = 'simplex'
)
Run the code above in your browser using DataLab